Home > Actuators > MODEL 11-480
>
<
GROUP 11 MULTI-TURN ROTARY ACTUATOR

MODEL 11-480

Group 11 Multi-Turn actuator is perfect for rising and non-rising stem applications for non-critical applications.

AVAILABLE TORQUE AND TIMING COMBINATIONS FOR THE MODEL 11-480

FULL TRAVEL (TURNS)
TORQUE
(LB-FT)
STROKE TIME*
(SECONDS/90°)
9
90
1
14
90
1.5
25
90
2.7
45
90
4.9
68
90
7.5
125
90
13.7
225
90
24.7
405
90
44.5
* Stroke times listed are for 60 Hz operation and for a gear ratio of 1:1.
DIGITAL CONTROL MODULE (DCM-3)

Beck’s DCM-3 provides modulating control of the drive in response to standard control system signals.

Notable features include:

  • Convenient user interface for calibration and drive status.
  • HART® compatibility.
  • Compatible with common asset management systems.
  • Receives control signals directly, eliminating the need for contact protection devices, relays, switches and reversing starters.
  • Designed to operate continuously at temperatures from -40º F to 185º F (-40° to 85° C).
  • Initiates shaft movement in steps ranging from 0.10% to 0.25% of span, depending on the timing of the gear train.
CONTACTLESS POSITION SENSOR (CPS-5)

Beck’s patented CPS-5 technology has been providing reliable control feedback with infinite resolution in our products for many years.

  • Utilizes a unique ferrite magnetic design with no contacting or wiping surfaces to wear or intermittently lose contact.
  • The ferrite rotor is driven directly by the output shaft through anti-backlash gearing.
  • A 4–20 mA position feedback signal is available for remote indication.

FACTORY CALIBRATION

All Beck drives are set-up and calibrated to the customer specification. No electrical adjustments are required before installation. Additional Features available on Beck Control Electronics

Pre-Determined Action Upon Loss of Input Signal
Stall Protection
Split Signal Operation for Control of Multiple Drives
Temperature Sensing with Alarm
BECK DRIVE MOTOR: PRECISE, RELIABLE CONTROL

Together with Beck’s control electronics and rugged gear train, Beck motors provide the precise, reliable positioning required for modern control loops.

  • Never overheats or burns out, even under demanding modulating control or stalled conditions.
  • Reaches full speed and torque in less than 50 milliseconds and stops within 25 milliseconds, eliminating deadtime.
  • Provides extremely accurate positioning in modulating applications.
  • Will not coast or overshoot the desired position.
  • Low current draw of 0.16 A to 3.0 A, and therefore low power consumption, eliminates the need for relays and permits the use of uninterruptible power supplies.
  • Maintenance-free with double-lipped, grease-sealed bearings.
ELECTRIC HANDSWITCH: TIME-SAVING LOCAL OPERATION

Dampers or valves may be operated at their individual locations with the built-in electric Handswitch. This saves time during installation and troubleshooting, allowing on-line adjustments to be made quickly and easily by bypassing the electronics in the drive and control system.

The Handswitch also serves as an electrical backup in the event of control system failure.

AUXILIARY AND OVER-TRAVEL LIMIT SWITCHES

Two over-travel limit switches and up to four auxiliary switches are provided on Beck drives.

  • SPDT switches rated for a minimum of 6 A at 120 V ac, (three times maximum motor current for most models) to ensure long life.
  • Field-adjustable to operate at any point in the drive’s travel range.
  • May initiate secondary functions or provide remote indication of drive position.
  • Eliminates unreliable and maintenance- intensive proximity switches.

FACTORY CALIBRATION

All Beck drives are set-up and calibrated to the customer specification. No electrical adjustments are required before installation. Additional Features available on Beck Control Electronics

Pre-Determined Action Upon Loss of Input Signal
Stall Protection
Split Signal Operation for Control of Multiple Drives
Temperature Sensing with Alarm
DRIVE TRAIN: DURABLE AND EFFICIENT

Beck’s durable gear train maintains accurate, consistent control element positioning even under the demanding conditions of an active control loop.

  • Gear trains employ a unique, all spur gear construction of heat-treated alloy steels and ductile iron.
  • Efficient, wide-face spur gearing virtually eliminates wear-induced backlash and positioning inaccuracies.
  • Durable design provides up to 4 days of protection against intermittent or extended accidental stalls.
  • Integral self-locking mechanism ensures that drives hold a load with the motor de-energized.
MANUAL HANDWHEEL: CONVENIENT MANUAL CONTROL WITHOUT DECLUTCH

An easy-to-turn, spoke-free Handwheel is incorporated into the Group 11 design to allow manual operation during installation or power outages.

  • Move valves and dampers to any position smoothly and easily without power, even under full load conditions.
  • Mechanical stops in housing prevent manual overtravel.
HOUSING: SUPERIOR PROTECTION WITH CONVENIENT ACCESS TO COMPONENTS

Drive cutaway view displaying
individual compartments

Beck drives feature a cast aluminum body with individual compartments to protect components from moisture and dirt, and allow easy access for installation and calibration.

  • Precision-machined aluminum alloy castings with corrosionresistant poly-urethane paint provide a rugged, dust-tight, weatherproof NEMA 4X enclosure.
  • Individual compartments protect all major components: Motor, DCM, CPS-2, gear train and installation wiring terminal board.
  • Each compartment can be accessed without exposing other components.
MOUNTING VERSATILITY: MOUNT IN ANY ORIENTATION FOR GREATER INSTALLATION FLEXIBILITY

Group 11 Beck drives are designed to be mounted in any convenient position. The no oil bath design eliminates the potential for leaks.

As long as housing compartments remain accessible, there are no mounting orientation limits.

FACTORY CALIBRATION

All Beck drives are set-up and calibrated to the customer specification. No electrical adjustments are required before installation. Additional Features available on Beck Control Electronics

Pre-Determined Action Upon Loss of Input Signal
Stall Protection
Split Signal Operation for Control of Multiple Drives
Temperature Sensing with Alarm

CONTROL OPTION

Group 11 Beck drives have a model number such as 11-150, 11-160, 11-200, 11-260, 11-300, 11-360, 11-400, 11-460, 11-430, or 11-480. Each of these drives has the capability to be equipped with different electronics combinations, which are called control options. The control option number will replace the last zero in the model number when specifying a drive model and control option. For example, a model 11-400 drive that is setup to use the control option 9 electronics would be considered a model 11-409 drive. A basic description for each control option is provided below. For details on the electronics components, please visit the Group 11 Electronics section.

9CONTROL
OPTION
CONTROL MODE
Modulating
INSTALLED CONTROL BOARD
DCM
STANDARD CONTROL INPUT
4-20 mA
INSTALLED POSITION SENSOR
CPS
STANDARD POSITION FEEDBACK
4–20 mA
DESCRIPTION

The standard modulating drive offering is the control option 9. Control option 9 units are equipped with the Beck DCM-3 (Digital Control Module) and CPS (Contactless Position Sensor). The option 9 drives may be controlled with a 4-20 mA or 1-5Vdc signal and have an integral 4-20 mA position feedback signal. The microprocessor based DCM provides a multitude of flexibility for setup, calibration, and diagnostics including HART communications, on-board pushbuttons for calibrating stroke, on-board diagnostic status, stall protection circuitry, and status alerts.

4CONTROL
OPTION
CONTROL MODE
up to 5-position
INSTALLED CONTROL BOARD
None
STANDARD CONTROL INPUT
120 V ac
INSTALLED POSITION SENSOR
None
STANDARD POSITION FEEDBACK
None
DESCRIPTION

The control option 4 drive is a Multi-position unit controlled with 120 VAC direct to the motor through a series of camoperated limit switches. The drive may be factory configured for three to six distinct positions anywhere in travel including two end-of-travel positions.

3CONTROL
OPTION
CONTROL MODE
2-position (open/close)
INSTALLED CONTROL BOARD
None
STANDARD CONTROL INPUT
120 V ac
INSTALLED POSITION SENSOR
None
STANDARD POSITION FEEDBACK
None
DESCRIPTION

The control option 3 drive is an open/close unit controlled with 120 VAC direct to the motor. When the drive hits the limit switch at either of the two end-of-travel positions, power is cut to the motor.

Modulating Control

Digital Control Module (DCM) Electronic Signal Receiver (ESR) Direct AC
Input Signal Options See Control Option 9 See Control Option 7 N/A
Adjustability for Split Range Operation 4 to 1 2 to 1 N/A
Deadband 0.6% of span (configurable) 0.6% of span N/A
Minimum Step 0.1% typical 0.15% typical 0.1° function of control
system capabilities
Feedback Options See Control Option 9 See Control Option 7 See Control Option 5 & 6
Stall Protection (Protects drive and driven elements under stall conditions) Standard. Integral to electronics. Time to stall is configurable from 300 seconds down to 30 seconds. Optional. Requires a Stall Protection Module (SPM) to shut off power to the motor.

Note: (1) Models approved for use in Hazardous classified locations are available—contact a Beck Sales or Application Engineer for details.

Input Power

120 V ac, single-phase
240 V ac, single-phase

Operating Conditions

-40° to 85° C. (-40° to 185° F.), 0% to 99% relative humidity

Isolation

Demand Input and Position Feedback signals are isolated from the ground and the ac power line.

Action on Loss of Power

Stays in place.


Action on Loss of Input Signal
(Power On)

Stays in place or, on some drives, is field configurable to move to any preset position.

Limit Switches

Two SPDT switches (one for each direction of travel) provide over-travel protection.

Auxiliary Switches

Up to four 6 A, 120 V ac switches available. Switches are labeled S1 to S4 and are cam-operated and field-adjustable.

Handswitch

Permits local electrical operation, independent of controller signal. Standard on all units. An optional auxiliary contact can be used to indicate that the Handswitch is in “AUTO” mode or to sound an alarm if it is taken out of
“AUTO”.

Instruction Manual # And Rev *
File Type
MODEL #S
CONTROL OPTION
Manufacture Date *
80-1103-04 Rev 1.1
PDF
11-489
9
All
80-1100-24 Rev 1.2
PDF
11-483 & 11-484
3 & 4
All
Dimension Drawing # *
Model #s *
Control Option *
Additional Options
18-0480-01o
PDF
11-48X
All
-
Dimension Drawing # *
Model #s *
Voltage *
Control Option *
Auxiliary Switches *
Notes
17-5503-65o
PDF
11-483
120
3
4
aux contact handswitch
17-5509-55o
PDF
11-489
120
9
4
aux contact handswitch

HOW TO ORDER

Beck Group 11 Quarter-Turn valve actuators are available in several basic models, and are furnished with either a bracket and linkage hardware package for connection to your valve or a direct-mount shaft to shaft hardware package for connection to your valve. The following instructions are intended to make it easy to specify and order Beck Group 11 quarter-turn rotary valve actuators. If questions arise concerning additional options or control modes, contact your Beck Sales Engineer.

Complete instruction manuals are furnished with each drive order.

01
DETERMINE REQUIRED PARAMETERS
  • Basic model number
  • Control option
  • Torque (lb-ft)
  • Timing (sec./100°)
  • Number of auxiliary switches
02
SPECIFY FULL MODEL NUMBER

Using the information above, fill out the full model number according to the following formula:

03
PROVIDE THE FOLLOWING ADDITIONAL INFORMATION
  • Desired control input signal
  • Desired power (120 or 240 V, 60 or 50 Hz)
  • Direction of rotation desired on increasing signal: Clockwise (CW) or Counterclockwise (CCW) (The resulting rotation for direct-coupled actuators will be opposite that of the valve).
  • Desired optional control features
04
PROVIDE THE FOLLOWING INFORMATION FOR VALVE APPLICATIONS:

a. Valve specification including:

  • Beck-supplied or customer-supplied
  • Manufacturer
  • Size
  • Style
  • Materials of construction

b. Characteristics of flowing media.
c. Maximum, normal and minimum inlet pressure.
d. Maximum, normal, minimum and shutoff pressure drop.
e. Maximum, normal and minimum flow rate and direction.
f. Line size and schedule including flange requirements.

05
SEND YOUR ORDER DIRECTLY TO:
11 Terry Drive, Newtown, PA, USA
For applications assistance, contact a Beck sales or application engineer:
215-968-4600
sales@haroldbeck.com
Build your Actuator